|
|
|
EpoxySystems' Product #260 Corrosion Resistant Epoxy Protective Primer/Coating
DESCRIPTION: PRODUCT #260 Corrosion Resistant Epoxy Protective Primer and Coating are two-component, 100% solids epoxy coatings based on multi-functional high performance resin and anti-corrosive pigment. PRODUCT #260 is used as a two coat system. PRODUCT #260 provides corrosion resistant protection to steel and other metals. PRODUCT #260 has excellent resistance to chemicals up to 300°F, and hot water resistance at temperatures up to 250°F under continuous immersion. PRODUCT #260 is formulated in a convenient 2 to 1 ratio, by volume mix ratio and has a long pot life to simplify application. The primer is green and the topcoat is blue. (Other colors are available as special order product.) PRODUCT #260 is particularly effective in applications which entail force curing, either as pre-immersion or during immersion service.
ADVANTAGES:
WHERE TO USE: For Chemical Protection of:
PHYSICAL PROPERTIES:
Cured Film -
For your specific chemical problem, consult Epoxy Systems, Inc. directly.
SURFACE PREPARATION: Steel Surfaces: Steel surfaces should be abrasive blasted to a commercial gray metal finish as specified by the Steel Structures Painting Council SP-6. For immersion service, blast to near white blast SSPC SP-10.
MIXING: Stir Components "A" & "B" thoroughly before mixing. Combine two parts by volume of "A" with one part by volume of "B" (mixing ratio 2:1). Mix for not less than three minutes using a slow speed drill (300 to 600 rpm) and EpoxySystems’ -Mixing Paddle. Scrape side and bottom to ensure through mixing. Avoid entrapping air. Apply immediately after mixing.
APPLICATION: PRODUCT #260 Corrosion Resistant Epoxy Protective Primer and Coating may be applied by brush, roller, or spray. All spray equipment must employ traps to prevent water and oil from contaminating coating. Thinning may be required for brushing and rolling. Heating may be required for spraying. Heating will shorten pot life to 20 minutes at 100°F. Apply immediately after mixing. Apply 10 mils wet film thickness. Apply topcoat after primer is tack free between 4 and 24 hours. If heated, the tack free time will be reduced.
COVERAGE: 100-200 square feet per gallon (per coat), dependent upon surface texture and desired thickness.
SHELF LIFE: 2 years
PACKAGING: PRODUCT #260 Corrosion Resistant Epoxy Protective Primer and Coating is packaged in 3-gallon and 15-gallon kits. CAUTION: WARNING! "A" Component contains epoxy resin. DANGER! "B" Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with eyes or skin. Wear protective clothing, goggles, gloves, and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling. FIRST AID: In case of skin contact, immediately wash with soap and water. In case of eye contact, flush with copious amounts of water for at least 15 minutes. Remove contaminated clothing and shoes. If irritation persists, seek medical attention. Wash clothing before reuse. FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN |
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
