|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home

This Material requires a minimum product purchase. Please see our Products That Require a Minimum Order Page, or contact Epoxy.com for more information.

BASIC USES:

Once cured, EPOXYSYSTEMS’ PRODUCT #417 allows expansion and contraction over a broad temperature range and maintains waterproofing properties under continuous exposure to water. EPOXYSYSTEMS’ PRODUCT #417 Type II has a thixotropic consistency and may be used on vertical as well as horizontal surfaces. EPOXYSYSTEMS’ PRODUCT #417. remains flexible from -75°F to +175°F (-59°C to 79°C). EPOXYSYSTEMS’ PRODUCT #417 waterproof membrane is intended for use wherever overflow water must be contained.

Suggested areas of application are as follows:

• Waterproofing in between concrete slabs, such as parking decks, roof decks or courtyard areas over subterranean parking.

• Waterproofing below grade exterior walls or foundations and basements or other structures that are to be backfilled.

• Waterproofing inside planter boxes.

• Waterproofing under terrazzo or tile floors.

• Waterproofing under shower-pans, kitchen, laundry and bathroom floors.

• Waterproofing inside of elevated swimming pools.

• Waterproofing of occupied areas under malls, plazas and promenades.

• Water Tanks: EPOXYSYSTEMS’ PRODUCT #417 has been used with outstanding success as a lining for emergency water storage tanks. The EPOXYSYSTEMS’ PRODUCT #417 bridges hairline cracks and because of the materials flexibility, allows them to move with changes in temperature. The product is fully bonded to the substrate so water cannot flow underneath the lining as it can with sheet lining materials.

 

• EPOXYSYSTEMS’ PRODUCT #417 is a single-component compound that may be used directly from the container with no mixing required.

• The addition of catalysts are not necessary, as EPOXYSYSTEMS’ PRODUCT #417 is a moisture-cured compound.

• May be applied by spray equipment, brush, roller, squeegee or trowel, without the need for heating the material.

• May be applied over concrete, stone, brick, cement blocks, wood, metal, asbestos and most other surfaces.

• EPOXYSYSTEMS’ PRODUCT #417 cuts cost of application by eliminating mixing, splicing, sealing tapes, adhesives and other labor consuming methods required when installing other conventional types of waterproofing systems.

• The superior flexibility and elongation properties of EPOXYSYSTEMS’ PRODUCT #417 allows expansion and contraction with the substrate, without cracking or becoming brittle.

• Does not contain any potentially hazardous coal tar.

APPLICATION:

• EPOXYSYSTEMS’ PRODUCT #417 is best applied by airless spray. However, when the job does not lend itself to spraying, it may also be applied by roller, brush or squeegee.

• All cracks over 1/16" (1.6mm) in width must be filled and covered with EPOXYSYSTEMS’ PRODUCT #417 Non-sag. This product may be applied by trowel or caulking gun. There is no need to wait for this product to cure before applying the EPOXYSYSTEMS’ PRODUCT #417 since they are completely compatible.

• A dry film thickness of 60 mils (1.5mm) is recommended over concrete surfaces. Extremely porous substrates should be filled prior to coating or receive additional EPOXYSYSTEMS’ PRODUCT #417

• EPOXYSYSTEMS’ PRODUCT #417 may be used in a single 60 mil (1.5mm) application over sound surfaces without danger of gassing. Application must be made uniformly to avoid thin spots and care must be taken to avoid pinholes and repair them should they occur. Coverage to obtain 60 dry mils is 20 sq. ft./gallon (0.48 m²/Liter). Where a two coats application is preferred, two coats at 40 sq. ft./gallon (0.96 m²/liter) per coat are to be applied, allowing a 24 hour cure time between coats.

• Protection board must be used prior to backfilling or pouring the concrete topping slab.

LIMITATIONS:
Containers that have been opened must be used within one or two days since it is a moisture-reactive material. It sets up when exposed to air. All surfaces must be completely free of foreign matter and dry before recoating it with EPOXYSYSTEMS’ PRODUCT #417..

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com 

352-489-1625   Fax line to all Departments
 
www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

Copyright © 1994-2008 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

[Technical Data Sheets in Adobe Acrobat Format][MSDSs in Adobe Acrobat Format][Online- Ordering Authorization Form]

Secure Login