|
|
EpoxySystems' Product #671 Conductive Primer/Sealer Description EpoxySystems’ Product #671 is a low viscosity, two component, carbon filled, polyamide modified conductive primer/sealer formulated with special wetting agents to provide maximum penetration into concrete surfaces. Product #671 is ideal for both new and old concrete surfaces. Product #671 provides excellent resistance to wear, and can be used either alone or as a conductive sealer or as a conductive primer when used with EpoxySystems’ product #674 Electro-Static Dissipating Urethane Topcoat and EpoxySystems’ Conductive Systems. Advantages
Considerations
Application Surface Preparation: Concrete must be in sound condition and properly prepared per manufacturer’s recommendations. Refer to EpoxySystems Surface Preparation Guidelines, available from EpoxySystems’ Technical Support Department. Mixing Instructions: Stir Part A (Resin) and part B (Hardener) with a power mixer. Allow 30 minutes before using. Remix. Mix only material needed for 4-6 hours I nstallation: Product #671 produces the best results when applied with a medium napped shed resistant roller, like the type available from EpoxySystems. It may also be applied with brush, squeegee, and conventional or airless sprayer. Spread #671 at a rate of 200 sf per gallon to yield approximately 4 dry mils. Check conductivity of the area prior to recoating. If Product #671 is being used alone as a sealer the recommended dry film thickness of 8-10 mils (2 coats @ 200 sf per gallon). Roughen the surface if allowed to cure more than 24 hours between coats. Be sure to verify conductivity after completing installation.Do not apply to surfaces below 50° F or above 120° F. Do not apply over damp or wet surfaces. Cleanup Clean up immediately with Xylene solvent. Remove from skin while still wet, wash with soap and water. Consult MSDS for safety and health precautions. Technical Data
Cautions Flammable- Avoid all sources of ignition during mixing, application and curing The Hardener, Part B, and mixture of Base, Part A, with Hardener, Part B, can cause skin and eye burns along with an allergic reaction. EpoxySystems’ Product #671 is sold without warranty as to performance expressed or implied. Personal testing is recommended to determine if the product is suitable for particular conditions. See Material Safety Data Sheets for full safety precautions. |
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
